We proposed a through-hole based transformer between microstrip line and post-wall waveguide (PWW). The transformer is based on a through-hole which is electrically separated from top and bottom broad walls of a waveguide by ring-shaped spaces. The proposed transformer shows a considerable merit compared with a conventional one based on blind-via in terms of fabrication and cost because it can be realized by through-holes in general printed-circuit-board technology. We selected liquid crystal polymer (LCP) as the material of substrates because of its lower dielectric loss and easy fabrication. The transformer was fabricated and measured. The loss associated with the mode conversion is estimated to be around 0.32,dB, and the bandwidth for a reflection smaller than $-15$,dB is 8,GHz, i.e., from 59 to 67,GHz.

A waveguide 2-plane hybrid coupler with two operating bands is proposed. The cross-sectional shape of the coupled region inside the proposed coupler is designed with a two-dimensional arbitrary geometry sorting method. Simulations of the proposed hybrid coupler has a fractional bandwidth (FBW) of 2.17% at the center of 24.99GHz, and at the center of 28.28GHz an FBW of 6.13%. The proposed coupler is analyzed by the mode-matching finite-element hybrid method, and the final result is obtained using a genetic algorithm. The analyzed result of the coupling for the main modes in the coupled region is presented. The design result is confirmed by measurements.

As a first step towards the realization of high-efficiency on-chip antennas for 60GHz-band wireless personal area networks, this paper proposes the fabrication of a patch antenna placed on a 200µm thick dielectric resin and fed through a hole in a silicon chip. Despite the large tan δ of the adopted material (0.015 at 50GHz), the thick resin reduces the conductor loss at the radiating element and a radiation efficiency of 78%, which includes the connecting loss from the bottom is predicted by simulation. This calculated value is verified in the millimeter-wave band by experiments in a reverberation chamber. Six stirrers are installed, one on each wall in the chamber, to create a statistical Rayleigh environment. The manufactured prototype antenna with a test jig demonstrates the radiation efficiency of 75% in the reverberation chamber. This agrees well with the simulated value of 76%, while the statistical measurement uncertainty of our handmade reverberation chamber is calculated as ±0.14dB.

A design of a linearly-polarized non-resonant waveguide broad-wall transverse slot linear array with suppressed grating lobes is presented. Each unit element in the array consists of a transverse slot, an inductive post and a parasitic dipole-pair at a height of half of the free space wavelength. It is designed as an isolated unit without considering mutual coupling by using the Method of Moments (MoM) for radiation suppression in grating beam direction and reflection cancellation at the input. The elements thus designed are used in a travelling wave array environment. It is predicted that the reflection is less than -20 dB at 11.95 GHz while the grating lobes are suppressed by more than 15 dB. The design and the characteristics of the array are confirmed by measurements.

An alignment control system using beam-tilting 1-D arrays for a 120-GHz-band corporate-feed 2-D waveguide-slot array antenna is presented. The 2-D waveguide-slot array antenna transmits data, and the 1-D arrays are used to determine array alignment. We design two types of 1-D array antenna and fabricate a corporate-feed 2-D waveguide-slot array antenna surrounded by four beam-tilting 1-D arrays. We then construct an alignment control system and evaluate the performance of the control. We find that the angular accuracy of the antenna alignment control was within ±1deg.

Post-wall waveguide with a linear array of reflection-canceling slot pairs and center-feed is designed to cancel the frequency dependent tilting of the main beam and enhance the bandwidth of the antenna boresight gain. The array is fed at the center of the waveguide from the backside; the length of the radiating waveguide is halved and the long line effect in traveling wave operation is suppressed. Authors establish the array design procedure in separate steps to reduce the computational load in the iterative optimization by using Ansoft HFSS simulator. A center-feed linear array as well as an end-feed equivalent with uniform excitation is designed for 25.6 GHz operation and measured. The measured performances confirm the design and the advantage of the centre-feed; a frequency independent boresight beam is observed and the frequency bandwidth for 3 dB gain reduction is enhanced by 1.5 times compared to the end-feed array.

We propose an aperture coupling E-bend with step structure as a robust post-wall waveguide interface to an external standard waveguide in which the posts are separated from the aperture. A 61.25 GHz model transformer gives 11.4% bandwidth for the reflection below -25 dB by using a 1.2 mm-height dielectric substrate. We have compared the mechanical tolerances of both the conventional straight structure and the proposed step structure. The step structure is more robust against mechanical errors than the conventional one. Another advantage is that the accuracy of the analysis model for the post-wall to metal-wall replacement is enhanced for the step structure.

The center-feed in a single-layer slotted waveguide array[1]-[3] is one of the key components in polarization division duplex (PDD) wireless systems. Two center-feed arrays with orthogonal polarization and boresight beams are orthogonally arranged side-by-side for transmission and reception, simultaneously. Each antenna has extremely high XPD (almost 50 dB in measurement) and a very high isolation (over 80 dB in measurement) between two arrays is observed provided the symmetry of slot arrangement is preserved [4]. Unfortunately, the area blocked by the center feed causes high sidelobe levels. This paper proposes the ridged cross-junction multiple-way power divider for realizing blockage reduction and symmetrical slot arrangement at the same time.

We proposed a new architecture of antenna, transmitter and receiver feeding configuration for small synthetic aperture radar (SAR) that is compatible with 100kg class satellite. Promising applications are constellations of earth observations together with optical sensors, and responsive, disaster monitoring missions. The SAR antenna is a deployable, passive, honeycomb panel antenna with slot array that can be stowed compactly. RF (radio frequency) instruments are in a satellite body and RF signal is fed to a deployable antenna through non-contacting choke flanges at deployable hinges. This paper describes its development strategy and the present development status of the small spaceborne SAR based on this architecture.

A radial line slot antenna (RLSA) is a high gain and high efficiency planar antenna proposed for DBS subscribers. Spirally arrayed slots are excited by a cylindrical wave with the rotational symmetry. In a small sized antenna where large slot coupling is adopted, aperture efficiency reduction due to rotational asymmetry associated with a spiral arrangement of the slots becomes notable. Authors proposed a RLSA with a concentric slot arrangement excited by a rotating mode in order to enhance the rotational symmetry. This is the first report of the normal operation of a rotating mode RLSA fed by a cavity resonator. The experiments confirm the basic operation of this novel antenna; the gain of 27.8dBi and the efficiency of 68% is measured at 11.85GHz for the RLSA with 0.24mφ.

This paper presents the loss factors in the post-wall waveguide-fed parallel-plate slot array antenna in the millimeter-wave band. At first, transmission loss is evaluated per unit length by measuring the losses of post-wall waveguides on various substrates with different thicknesses in different bands. Measured results of the frequency dependence agree with theoretical predictions using the effective conductivity and the complex permittivity obtained by the whispering gallery mode resonator method. Then the authors evaluate the antennas with various sizes at 76.5 GHz. The antenna efficiency is evaluated by taking into account the loss factors related to: the transmission loss both in the feed and the parallel plate waveguides, the aperture efficiency and the insertion loss and the reflection of the transition. Also, the loss due to the locally-perturbed currents by the slot radiation is evaluated. The sum of the losses in the prediction quantitatively agrees with the measurement.

Transitions between a post-wall waveguide and a microstrip line are proposed as the key components for cost-effective millimeter-wave modules. A transition with a coaxial structure is investigated for LTCC laminated layers and 11.3% bandwidth for the reflection smaller than -15 dB is realized in 60 GHz band. The overall connector loss with 1 cm post-wall would be about 0.8 dB. The degradation due to fabrication error is also assessed. The transition in LTCC substrate fulfills electrical and manufacturing demands in millimeter-wave bands.

As one functionality of the wireless distributed network (WDN) enabling flexible wireless networks, it is supposed that a dynamic spectrum access is applied to OFDM systems for superior radio resource management. As a basic technology for such WDN, our study deals with the OFDM signal detection based on its cyclostationary feature. Previous relevant studies mainly relied on software simulations based on the Monte Carlo method. This paper analytically clarifies the relationship between the design parameters of the detector and its detection performance. The detection performance is formulated by using multiple design parameters including the transfer function of the receive filter. A hardware experiment with radio frequency (RF) signals is also carried out by using the detector consisting of an RF unit and FPGA. Thereby, it is verified that the detection characteristics represented by the false-alarm and non-detection probabilities calculated by the analytical formula agree well with those obtained by the hardware experiment. Our analysis and experiment results are useful for the parameter design of the signal detector to satisfy required performance criteria.

A wideband design of the waveguide short-slot 2-plane coupler with 2×2 input/output ports is designed, fabricated, and evaluated. Using coupling coefficients of complementary propagating modes which are TE11, TE21, and TE30 modes, the flatness of the output amplitudes of 2-plane coupler is improved. The coupler operates from 4.96GHz to 5.27GHz (bandwidth 6.1%) which is wider than the former coupler without considering the complementary propagating mode from 5.04GHz to 5.17GHz (bandwidth 2.5%).

This paper presents the excitation coefficient optimization of slot array antennas for increasing channel capacity in 2×2-mode two-dimensional ROM (rectangular coordinate orthogonal) transmission. Because the ROM transmission is for non-far region communication, the transmission between Tx (transmission) and Rx (reception) antennas increases when the antennas radiate beams inwardly. At first, we design the excitation coefficients of the slot arrays in order to enhance the transmission rate for a given transmission distance. Then, we fabricate monopulse corporate-feed waveguide slot array antennas that have the designed excitation amplitude and phase in the 60-GHz band for the 2×2-mode two-dimensional ROM transmission. The measured transmission between the fabricated Tx and Rx antennas increases at the given propagation distance and agrees with the simulation.

A multibeam massive multiple input multiple output (MIMO) configuration employs beam selection with high power in the analog part and executes a blind algorithm such as the independent component analysis (ICA), which does not require channel state information in the digital part. Two-dimensional (2-D) multibeams are considered in actual power losses and beam steering errors regarding the multibeam patterns. However, the performance of these 2-D beams depends on the beam pattern of the multibeams, and they are not optimal multibeam patterns suitable for multibeam massive MIMO configurations. In this study, we clarify the performance difference due to the difference of the multibeam pattern and consider the multibeam pattern suitable for the system condition. Specifically, the optimal multibeam pattern was determined with the element spacing and beamwidth of the element directivity as parameters, and the effectiveness of the proposed method was verified via computer simulations.

A novel design technique for two-dimensional (2-D) waveguide slot arrays is proposed in this paper that combines a full-wave method of moments (MoM) analysis and an equivalent circuit with the explicit restraint of input matching. The admittance and slot spacing are determined first in an equivalent circuit to realize the desired distribution of power dissipation and phase, with the explicit restraint of input matching. Secondly by applying a full-wave MoM analysis to the finite 2-D array, slot parameters are iteratively determined to realize the active admittance designed above where slot mutual coupling and wall thickness are fully taken into account. The admittance, treated as the key parameter in the equivalent circuit corresponds to the power dissipation of the slots but not to the slot voltage, which is directly synthesized from the radiation pattern. The initial value of the power dissipation is assumed to be proportional to the square of the amplitude of the desired slot voltage. This assumption leads to a feedback procedure, because the resultant slot voltage distribution generally differs from the desired ones due to the effect of non-uniformity in the characteristic impedance on slot apertures. This slot voltage error is used to renew the initial distribution of power dissipation in the equivalent circuit. Generally, only one feedback cycle is needed. Two 2427-element arrays with uniform and Taylor distributions were designed and fabricated at 25.3 GHz. The measured overall reflections for both antennas were suppressed below -18 dB over the 24.3-26.3 GHz frequency range. High aperture efficiencies of 86.8% and 55.1% were realized for the antennas with uniform and Taylor distributions, the latter of which has very low sidelobes below -33 dB in both the E- and H-planes.

Interfaces between a coaxial structure and a post-wall waveguide are proposed as the essential components for cost-effective millimeter-wave modules. PTFE substrate is selected in terms of loss and manufacturability. The reflection and the transmission characteristics are investigated. The short-stepped and the short-taper-stepped feeding structures provide 14.7% and 13.2% bandwidths for the reflection smaller than -15 dB, respectively. The 4640 mm2 size antenna fed by the short-stepped structure in PTFE substrate gives 27.3 dBi with 58.2% efficiency at 60.0 GHz. Feeding structures in PTFE substrate fulfill electrical and manufacturing demands in millimeter-wave bands.

A point-to-point fixed wireless access (FWA) system with a maximum throughput of 1Gbps has been developed in the 39GHz band. A double-layer plate-laminated waveguide slot array antenna is successfully realized with specific considerations of practical application. The antenna is designed so as to hold the VSWR under 1.5. The antenna input as well as feeding network is configured to reduce the antenna profile as well as the antenna weight. In addition, integrating the antenna into a wireless terminal is taken into account. A shielding wall, whose effectiveness is experimentally demonstrated, is set in the middle of the wireless terminal to achieve the spatial isolation of more than 65dB between two antennas on the H-plane. 30 test antennas are fabricated by diffusion bonding of thin metal plates, to investigate the tolerance and mass-productivity of this process. An aluminum antenna, which has the advantages of light weight and anti-aging, is also fabricated and evaluated with an eye to the future.

This paper presents a novel 60 GHz-band photonic-integrated array-antenna and module for radio-over-fiber (RoF)-based beam forming. An integrated photonic array-antennas (IPA), where eight photodiodes and 4×2 arrayed patch-antenna are integrated in a single board, is actually fabricated, and 3.5-Gbit/s QPSK digital signal transmission with beam forming of the IPA is experimentally demonstrated. In addition, a novel 60-GHz compact antenna module is proposed and fabricated for increasing the number of antenna elements and flexibility creating various beam patterns. The feasibility of beam forming operation for the proposed antenna module is confirmed by a 60-GHz RoF transmission experiment. The capability of detecting the mobile terminal direction, which is one of the indispensable functions for actual environment, is also studied. The obtained results in this paper will be useful for designing future radio access networks based on RoF transmission technology.